ادامه
در صورتی که قیمت ارزی محصول را در اختیار دارید پس از عضویت و ورود به سایت می توانید فرم مربوطه را تکمیل و به همراه تصویر پرفورمای شرکت سازنده ارسال نمایید تا کارشناسان ما در اسرع وقت نسبت به محاسبه هزینه های حمل و ترخیص و صدور پیش فاکتور ریالی اقدام نمایند. هزینه استفاده از این سرویس برای هر درخواست 25 یورو می باشد. صنایع معظم در صورت تمایل به استفاده از این خدمات می توانند بدون نیاز به عضویت و پرداخت هزینه درخواست خود را به همراه کپی پرفورمای شرکت سازنده به ایمیل enquiry@iranindustryexpo.com و یا فاکس 88206264 بنام شرکت مهندسی و بازرگانی مشگاد ارسال نمایند.
در صورت عقد قرار داد مبلغ دریافتی به حساب خریدار عودت می شود.
ادامه
اگر مجموعه شما جزو صنایع مادر و معظم در فیلد پالایشگاه ، پتروشیمی ، حفاری ، نیروگاه ، معادن و فلزات ، خودروسازی ، تولید مواد غذایی و دارویی و.... می باشد لطفا درخواست خود را بر روی سربرگ به فاکس 88206264 و یا ایمیل enquiry@iranindustryexpo.com بنام شرکت مهندسی و بازرگانی مشگاد ارسال فرمایید.
کارشناسان این مجموعه در اسرع وقت با شما تماس خواهند گرفت .
بازدیدکننده محترم، از اینکه سایت ایران اینداستری را برای منابع یابی انتخاب کرده اید، از شما سپاسگزاریم.
اطلاعاتی برای نماینده شرکت Gurit در ایران یافت نشد.
لطفا با انتخاب هر یک از بخش های فوق، درخواست خود را ارسال فرمایید تا توسط واحد بازرگانی ایران اینداستری اکسپو بررسی شود.
-
Other characteristics:
low-temperature curing
-
Resin type:
epoxy
Low temperature 70°C / 160°F curing. Faster cycle times at elevated temperature
Excellent balance of mechanical properties and toughness
Excellent surface finish
Long out-life - up to 4 weeks @ 18-22°C / 65-72°F
Range of compatible adhesive films and ancillary products
Suitable for vacuum bag, press or autoclave consolidation
Gurits SE 70 is a hot melt, low temperature cure, epoxy prepreg system. It has been developed for use in the construction of large components using low energy cure cycles. Excellent properties can be achieved with a processing temperature of just 70°C / 160°F. From this cure temperature the system exhibits very good mechanical properties and excellent toughness.
Cure temperature for a 16 hours cure cycle is 70°C / 160°F - this temperature allows less expensive tooling and ovens to be used, with lower thermal movement and distortion. Faster cures are available from higher cure temperatures. However, thicker sections (>10mm) will require the insertion of a suitable dwell into the cure cycle. Up to 20mm thick laminates may be moulded at 70°C / 160°F with a peak exotherm only slightly above the cure temperature.
Typical Applications
SE 70 is widely used in sandwich structures with honeycomb, foam and balsa cores, primarily with the toughened SA 70 Adhesive Film.