AHP200 series0 pages

AC-DC Converters
www.powersolve.co.uk

AHP 200 Series
Up to 212 Watts Output
Features
•
•
•
•
•
•
•
•

3.00” x 5.00” x 1.34”
High Power Density - 10.6 W/in3
Up to 90% Efficiency
5 V Standby & 12 V Fan Outputs
Active Current Share
Remote On/Off
Power Good Signal
48 VDC Input Versions Available (DAHP200 Series)

Electrical Specification
INPUT
Input Voltage
90-264 VAC
Input Frequency
47-63 Hz
Input Current
2.2 A max at 115 VAC, 1.1 A max at 230 VAC
Inrush Current
60 A max at 230 VAC, cold start at +25 ºC
Power Factor
>0.9 typical
Earth Leakage Current
1.1 mA max 264 VAC/50 Hz, 500 µA typical at 230 VAC/50 Hz, 290 µA typical at 115 VAC/60 Hz
OUTPUT
Output Voltage
See table
Output Voltage Trim
No user adjustment available
Initial Set Accuracy
V1: ±1%, V2: ±5%, V3: ±3%
Minimum Load
No minimum load required
Start Up Delay
<3 s maximum
Start Up Rise Time
20 ms maximum
Hold Up Time
16 ms minimum
Drift
<±0.2% after 20 min warm up
Line Regulation
V1: ±0.5%, V2: ±2%, V3: ±0.5%
Load Regulation
V1: ±1% 0-100% load, V2: ±1% 10-100% load, V3: ±1% 0-100% load
Cross Regulation
V2: ±10% 10-100% load change on V1
Over/Undershoot
<2% max at turn on/off for 12 V models, <5% for 24 V & 48 V models
Transient Response
<4% max deviation for a 25-75-25% load step. Output V1 returns to within 1% in 500 µs
Ripple & Noise
V1 & V3: 1%, V2: 2% pk-pk, 20 MHz BW
Overvoltage Protection
115-140% Vnom, recycle input to reset (output 1 only)
Overtemperature
Primary & secondary protection with Protection auto recovery
Overload Protection
110-140%, auto recovery output 1
Short Circuit Protection
Trip and restart (Hiccup mode)
Temperature Coefficient
0.05%/ºC
Remote On/Off
Uncommitted isolated opto-coupler diode, powered diode inhibits the supply
Current Share
Up to 3 supplies to share within 10%, derate total output to 90%
GENERAL
Efficiency
88% typical
Isolation
3000 VAC Input to Output, 1500 VAC Input to Ground, 500 VDC Output to Ground
Switching Frequency
80 kHz typical for PFC, 100 kHz typical for main converter
Power Density
10.6 W/In3
Signals
Combined PF & DC OK - Open collector referenced to output 0 V, transistor normally off when AC & output
good. PF provides >5 ms warning of loss of output from AC failure. DC OK provides warning of DC output failure.
MTBF
400 kHrs per MIL-HDBK-217F typical
ENVIRONMENTAL
Operating Temperature
-10 ºC to +70 ºC, derate linearly from +50 °C at 2.5%/°C to 50% at +70 °C
Cooling
12 CFM airflow required (see thermal considerations)
Operating Humidity
5-95% RH, non-condensing
Storage Temperature
-20 ºC to +85 ºC
Operating Altitude
3000 m
Shock
30 g pk, half sine 6 axes
Vibration
2 g, 5 Hz to 500 Hz, 3 axes
EMC & SAFETY
Emissions
EN55022, level B conducted, EN55022, level A radiated
Harmonic Currents
EN61000-3-2, class A
Voltage Flicker
EN61000-3-3
EFT/Burst
EN61000-4-4, level 3 Perf Criteria A
Surge
EN61000-4-5, level 3 Perf Criteria A
Conducted Immunity
EN61000-4-6, 10 Vrms, Perf Criteria A
Dips & Interruptions
EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms Perf Criteria A, B, B
Safety Approvals
CB report IEC60950-1:2001, CSA 22.2 No. 60950-1-03, TUV EN60950-1/A11:2004, CE Mark (LVD), CCC pending, contact sales

Powe
rsolve Electronics Ltd. 8A, Arnhem Road, Newbury, RG14 5RU. England
Tel:01635 521858 Fax: 01635 523771 Email: sales@powersolve.co.uk